国产亚洲欧美在线专区,四虎国产精品一区二区,四虎国产精品亚洲一区久久特色,亚洲综合欧美制服丝袜

Universal grinder plugging and bearing analysis
   Universal grinder clogged grinder use one of the fault, there may be problems in equipment design, but more due to the use of improper operation.
  (A) universal grinder feed too fast, the load increases, causing blockage. Feed, it is necessary to pay attention to the ammeter pointer deflection, if you exceed the rated current, indicating that the motor overload, overload for a long time, will burn out the motor. The emergence of this situation should immediately reduce or close to universal grinder hopper, you can also change the way of the feed by adding feeders to control the feed rate. Manual, automatic two feeders, the user should choose the right feeder according to the actual situation. Universal grinder speed, load, and load fluctuations. Therefore, the current universal grinder work is generally controlled at about 85% of the rated current.
  (B) the discharge pipe poor or blockage of the feed too fast, make universal grinder outlet to plug; mismatch and transportation equipment will result in the discharge pipe wind weakened or no wind after blocked. Clear through the send port change does not match the delivery of equipment to detect failure to adjust into the feed rate, the normal operation of equipment.
  (C) universal grinder hammer clips, aging, the closure of mesh holes, broken, crushed material moisture content is too high will make universal grinder blocked. Broken and badly aging hammer should be regularly updated to maintain the universal grinder in good working condition, and regularly check the screen, the crushed material moisture should be less than 14%, thereby enhancing production efficiency, but also the universal grinder congestion, enhance the reliability of the grinder work.
  (D) universal grinder 2 bearing rugged rotor and shredder rotor misalignment, make additional load bearing by the impact, causing bearing overheating. This happens, immediately stop troubleshooting, to avoid damage to bearing early.
  (E) universal grinder bearing lubricant too much, too little or aging is caused by the bearings to overheat and damage the main reason, therefore, be according to use the book requires time quantitative filling oil, general lubrication accounting for bearing space 70% -80% too much or too little is not conducive to bearing lubrication and heat transfer. Bearings to extend their useful life.
  (F) universal grinder bearing cap and shaft with tight, bearings and shaft with too tight or too loose will lead to bearing overheating. Once this occurs, equipment operation, we will send the friction sound and swing. Should be down to remove the bearings. Dressing friction parts, and then reassembled as required.
  (G) bearing overheated bearing is more important universal grinder parts, and its performance directly affects the normal operation of the universal grinder and production efficiency. Equipment during the operation, the user should pay special attention to the bearing temperature rise and noise of the bearing parts of the abnormal early.
Related News:
· Innovation, energy saving, environmental protectio  
· Vacuum dryer product performance characteristics a  
· Vacuum dryer used for inspection and debugging wor  
· Difficulties and reasons cannot start mixing machi  
· The correct operation method using vacuum dryer  
· Development advantages and characteristics of dome  
· The difference between the special vacuum dryer an  
· Detailed description of each component characteris  
· The dominant position in the whole vacuum dryer dr  
· Trough type mixer sometimes appear large area leak  
Related Products:
· PGL Spray Drying Granulator
· High speed mixer
· SET series double screw extrusion pelletizer
· VI forced mixer
· Mixing machine W series
· Powder machine ZSJ series vibrating screen
· FZ series of crushing granulator
· Chinese medicine grinder
· DWT series of drier for dehydrated vegetables
· Multi-layer belt dryer

Copyright 2013 Chang Zhou Zhizun Machinery Co.,Ltd All Rights Reserved.Design by Reach.
Tel:86.519-88906508 Fox:86.519-88902679 Add:Jiaoxi Changzhou Jiangsu Pro China P.C:213116

主站蜘蛛池模板: 无码av中文字幕免费放| 亚洲国产日韩a在线乱码| 自拍偷自拍亚洲精品情侣| 国产无遮挡吃胸膜奶免费看| 午夜亚洲aⅴ无码高潮片苍井空 | 亚洲国产成人va在线观看| 漂亮人妻被强中文字幕久久| 99久久精品国产一区二区蜜芽| 曰本丰满熟妇xxxx性| 亚洲精品久久国产高清| 精品国产一区二区三区无码| 亚洲国产成人手机在线观看| 久久18禁高潮出水呻吟娇喘| 亚洲精品无码久久久久sm| 日日噜噜夜夜狠狠久久蜜桃| 亚洲人成色99999在线观看| 97人妻精品一区二区三区| 亚洲v国产v天堂a无码二区| 日本护士吞精囗交gif| 最新国产aⅴ精品无码| 99精品国产福利一区二区| 男女爽爽无遮挡午夜视频| 免费无码国产欧美久久18| 国产女人爽的流水毛片| 成人免费无码大片a毛片18| 亚洲精品国产综合麻豆久久99 | 亚洲精品网站在线观看你懂的| 伊人久久大香线蕉av不变影院| 一本大道无码日韩精品影视_| 国产一区内射最近更新| 五月丁香六月综合av| 婷婷成人综合激情在线视频播放 | 亚洲色大成网站www在线| 2020国产精品香蕉在线观看| 久久久久人妻一区精品| 久久无码av一区二区三区| 蜜芽国产尤物av尤物在线看| 婷婷五月婷婷五月| 亚洲欧美另类久久久精品能播放的| 久久精品国产亚洲夜色av网站| 无码人妻在线一区二区三区免费 |